,

Five things you may not know about the Big Boy

by

Last year, a ground-breaking five-year landmark project to restore a Union Pacific Railroad Big Boy 4-8-8-4 to working order was accomplished, with No. 4014 making a star-studded appearance at the 150th anniversary of the linking the USA’s two coasts by rail.

The world has waited six decades to see a Union Pacific Railroad (UP) Big Boy 4-8-8-4 back in action – and now No. 4014, one of eight survivors of the behemoth class, has taken over as the biggest operational steam locomotive on the planet.

Union Pacific's Big Boy 4014 Steam Locomotive, in Cheyenne, Wyoming, USA

Here’s five things you perhaps didn’t know about the Big Boy…

Article continues below…
Advert

Enjoy more Heritage Railway reading in the four-weekly magazine.
Click here to subscribe & save.

Dimensions

The locomotives were 132 feet long and weighed 1.2 million pounds. Because of their great length, the frames of the Big Boys were “hinged,” or articulated, to allow them to negotiate curves.

Stood on its end, a Big Boy would be the height of a 13-storey building. One weighs more than a Boeing 747 fully loaded with passengers and has the power to pull 16 Statues of Liberty over a mountain. Minus the tender, the Big Boy has the longest engine body of any reciprocating steam locomotive. 

By today’s standards, each Big Boy cost around $4.4 million to construct.

Article continues below…
Advert

Why is it called the Big Boy?

According to a Union Pacific executive, the class was originally to have been called the ‘Wasatch’. However, one day while one of the engines was being built, an unknown worker scrawled ‘Big Boy’ in chalk on its front – and so the legendary name was born.

Speed

They were tested at speeds between 70 and 80 m.p.h. In regular service, Big Boys were limited to a top speed of 55 m.p.h. That is a very large mass of iron coming down the tracks at a very high speed. From the time the engineer applied the brakes, until the time the Big Boy and train came to a complete stop was between 1 to 1.5 miles

‘Big Boy’ No. 4014 at rest, having arrived at Rawlings on the evening of May 5, on the trip from its base in Cheyenne to Promontory Summit, Utah. Photo: Eiki Sekine

A bigger boy

Finally, as if the 4000s weren’t big enough, the Union Pacific actually contemplated ordering five additional 4-8-8-4s that would be even larger.

Article continues below…
Advert

As World War II dragged on, the Union Pacific needed additional power on its line to Los Angeles through southwest Utah. According to historian and artist Gil Bennett, plans were on the drawing board to build No. 4025-4029.

This third class of Big Boys was to measure 139 feet, 11 5/8 inches long and weighs just under 1.3 million pounds. All would be oil fired, instead of coal. The locomotive, itself, would be a foot longer than existing Big Boys.

Retirement

The last revenue-earning train hauled by a Big Boy ended its run early in the morning on July 21, 1959. Most were stored operational until 1961 and four remained in operational condition at Green River, Wyoming until 1962.

Article continues below…
Advert

Big Boy No. 4014 was delivered to Union Pacific in December 1941. The locomotive was retired in December 1961, having traveled 1,031,205 miles in its 20 years in service.

You may also be interested in…

Union Pacific "Big Boy"

Check out some great footage of the unboxing of Rivarossi (H0 1:87) Union Pacific, Class 4000 “Big Boy” 4014 Special Edition.

With a confounding length of 475mm (almost 19 inches), a 5-pole motor and brass flywheel, a DCC Ready 21-pin plug, handrails made from steel wire and much more, this locomotive is unlike any other and undeniably lines alongside other models as a classic.


Advert
Subscribe to Heritage Railway Magazine Enjoy more Heritage Railway reading in the four-weekly magazine. Click here to subscribe.

Article Tags:

About the Author